Top 10 common forklift mishaps ， forklift procedure ought to pay attention to these matters ！.

Don't take too lightly the forklift at work. If the operation is not good, there will certainly be significant crashes in mins, and there are many accidents involving forklifts.

Case 1: The forklift cargo blocked the chauffeur's sight, and the person in front could not be found, resulting in a moving crash.
Instance 2: In order to keep the equilibrium of the forklift when raising heavy products, the employees used their body weight as the counterweight, which almost created casualties.
Instance 3: The size of the forklift cargo surpasses the permitted width of the course and holds on the roadside rack, which practically triggers an accident.
Instance 4: Forklift is speeding up and rolls over during a turn.
Case 5: The forklift vehicle driver did not observe the pedestrian, and the pedestrian did not observe the forklift.
Situation 6: The forklift lifts the employees unlawfully, the forklift chauffeur does not wear the safety belt, the forklift lifter falls and the chauffeur is squashed when the forklift surrender.
Case 7: The forklift driver did not put on a seat belt and dropped from the automobile when it rolled over and was squashed.
Forklift procedure should pay attention to these issues ：.

Begin.
1. Before beginning, observe the surroundings, and after validating that there are no challenges that prevent the security of driving, honk the horn initially and then begin.
2. For cars with hydraulic ( atmospheric pressure) brakes, the brake hydraulic pressure ( atmospheric pressure) gauge need to be safe prior to starting.
3. When the forklift begins with a load, the motorist should initially confirm that the tons is stable and trusted.
4. The start has to be slow and constant.

Driving.
1. When driving, the height in between the bottom end of the fork and the ground should be kept at 300mm-400mm, and the pole should be slanted in reverse. .
2. Do not lift the fork too expensive when driving. When entering and leaving the task website or while driving, be careful that there will be no barriers in the sky. When the load is taking a trip, the fork has to not be raised too expensive, which will certainly affect the stability of the forklift. .
3. After dumping, the fork should be reduced to the typical driving placement prior to driving. .
4. When transforming, if there are pedestrians or vehicles nearby, the driving signal must be released first. High-speed sharp turns are restricted. High-speed sharp turns will certainly create the vehicle to lose lateral stability and tip over. .
5. When the forklift is downhill, it is purely restricted to switch off the flame and slide, and it is forbidden to brake all of a sudden while driving with tons unless there are unique conditions.
6. When the forklift is running, it must obey the traffic rules in the factory and need to maintain a specific safety and security range from the automobile ahead. .
7. When the forklift is running, the lots has to remain in the most affordable placement that does not prevent the driving, and the gantry needs to be effectively slanted back. The lots will not be elevated other than when piling or packing. .
8. The height of the tons should not block the chauffeur's sight. In special situations, when the item affects the forward vision, drive at a reduced rate when turning around.
9. It is prohibited to switch on the ramp, nor to drive across the ramp. .
10. The secure driving rate of the forklift in the factory area is 5 km/h, and it has to drive securely at a reduced speed when entering the manufacturing workshop location. .
11. When the forklift is lifted, lifted or driven, it is restricted for employees to base on the fork to hold products and play a balancing duty. .
12. If issues are discovered, they will be fixed and reported in a timely manner, and they will certainly never ever operate with ailments or hide them.

packing and unloading.
1. When fork-loading things, the distance between both forks ought to be adjusted as required to make the load of both forks balanced and not skewed, and one side of the product ought to protest the shelf. .
2. It is forbidden to collaborate with a single fork or make use of a fork top or draw. In special conditions, security indication need to be set up to advise bordering pedestrians. .
3. In the process of packing and unloading products, the forklift must be stopped with the brake. .
4. The speed of the automobile should be slow-moving and steady. Beware not to roll the wheels on the dunnage, so as not to extend the rolled items and injure people. .
5. When making use of a fork to fork the goods, the fork needs to be as deep as feasible under the load, and it needs to be noted that the fork idea should not touch other items or objects. The tons should be supported with minimal back tilt of the gantry to ensure that the lots does not slide in reverse. The pole can be tilted ahead a little when the load is reduced to permit easy placement of the tons and removal of the forks. .
6. It is forbidden to fork goods at broadband and ram hard objects with the fork head. .
7. When the forklift is working, it is restricted for individuals to stand around the fork, so as to avoid the collapse of the goods and injure people. .
8. Straining is prohibited, and it is restricted to utilize forks to raise employees to take part in high-altitude operations to avoid high-altitude falling mishaps. .
9. It is not enabled to utilize the brake inertia to slide, place, round or roll things. .
10. It is not permitted to make use of forks to pick, turn pallet unload.

Leaving .
1. It is forbidden to leave the forklift when the things on the fork are in the air. Before leaving the forklift, you need to dump the goods or reduced the fork frame.
2. Pull the emergency brake take care of to dead or dispirit the hand brake button.
3. The engine is switched off and the power is removed. (Except for unique conditions, such as the vehicle driver does not leave the lorry's view and does not go beyond 1 min).
4. Get rid of the secret. .

Forklift Operation Precautions.
1. Before and after the forklift operation, the appearance should be checked, and gas, lubing oil and air conditioning water must be added.
2. Check the safety efficiency of beginning, running and braking.
3. Check whether the lights and horn signals are complete and reliable.
4. Throughout the operation of the forklift, check whether the pressure and temperature level are typical.
5. After the forklift is running, the outside leakage needs to additionally be inspected and the seals ought to be changed in time.

Forklift Safety Operation Specifications.
1. You have to inspect before leaving the Stand-on Electric Pallet Stacker car;.
2. When you encounter a person in front of you during driving, you need to send a signal at a distance of 5 m;.
3. The driving speed in the manufacturing facility does not exceed 5 km/h;.
4. When driving, the nadir of the freight should be 0.3 m ~ 0.4 m in the air;.
5. The turning should not be also sharp to avoid the propensity of " complimentary turning";.
6. Adding and down the slope needs to be sluggish and consistent, and no switching on the slope is enabled.
7. Do not drive across the slope. When the gradient is above 10%, the vehicle needs to be driven backwards when worsening;.
8. When the forklift personnel lug the goods and move forward, if they run into large or hefty goods and most likely to the driver's line of vision, they should take the reversing workout
.
The "Eight Prohibitions" ought to be adhered to in the operation.
1. Single fork procedure is not allowed.
2. It is not enabled to raise the goods for long distance driving.
3. It is not enabled to grab the goods by turning over the pallet with the fork.
4. It is not enabled to straight shovel chemicals, flammables and other harmful chemicals with forks.
5. It is not permitted to use inertia force to grab the goods.
6. It is not permitted Electric Forklift Truck for Warehouse to use braking pressure to expatriation round or easy-to-roll objects.
7. It is not enabled to bring individuals to work with the pallet or fork, and it is strictly prohibited to stand under the fork after the fork is increased.
8. Do not drive side to side on inclines
.
Vehicle parking is not allowed under the list below problems.
1. Curves, narrow roads, railway crossings;.
2. Areas with a longitudinal incline more than 5%.
3. When there is an obstacle on one side of the road, the opposite side of the section with the exact same size as the barrier need to be within 20 meters at each end.

Web：https://www.onenforklifts.com/
Email：[email protected]
Phone：+86 13827083844